Evaluation of the Mechanical Properties of Coconut-Fiber- and Plastic-Fiber-Reinforced Concrete
Received: 22 November 2025 | Revised: 13 December 2025, 29 December 2025, and 4 January 2026 | Accepted: 13 January 2026 |Online: 4 April 2026
Corresponding author: Genesis Soriano Perez
Abstract
The usage of natural and recycled fibers in order to reinforce concrete was driven by the search for sustainable building materials. This study performs a comparative evaluation of the mechanical behavior of concrete using coconut and Polyethylene Terephthalate (PET) fibers. The concrete is mixed and cured under consistent conditions and each fiber type is evaluated separately within the same standardized base mix formulation to eliminate design variables. The considered dosages (0.5% and 1% coconut and 2% PET) represent practical optimums, determined through workability limits and prior research with the same concrete formulation. A Control Mix (CM) (27.46 MPa, or approximately 280 kg/cm²) was designed with fibers of different dosages acting as additional materials. The results suggest that coconut fibers are more effective than PET fibers as a reinforcing agent. Short Fibers (SFs) (100 mm) at a dosage of 1% exhibited the highest compressive strength, increasing it by 15.0%. In terms of flexural strength, Long coconut Fibers (LFs) (200 mm) at 1% were the most effective, increasing it by 13.7%. In contrast, PET fibers at 2% showed modest compression improvement (4.5%) and slight flexural strength reduction (−0.34%). The effectiveness of coconut fiber is due to its better adhesion to the cementitious matrix and its ability to act as a crack bridge, shifting the failure mode from brittle to cohesive with post-cracking structural integrity. These results show that coconut fiber can be used as a sustainable reinforcement material for nonstructural concrete applications and secondary elements.
Keywords:
concrete, fiber-reinforced concrete, natural fibers, recycled PET, mechanical properties, sustainability, coconut fiberDownloads
References
S. Hedjazi and D. Castillo, "Relationships among compressive strength and UPV of concrete reinforced with different types of fibers," Heliyon, vol. 6, no. 3, 2020, Art. no. e03646. DOI: https://doi.org/10.1016/j.heliyon.2020.e03646
Y. T. Altuncı, "A comprehensive study on the estimation of concrete compressive strength using machine learning models," Buildings, vol. 14, no. 12, 2024, Art. no. 3851. DOI: https://doi.org/10.3390/buildings14123851
J. Donaire-Ávila and A. Benavent-Climent, "Validación numérica del comportamiento cíclico de conexiones interiores en estructuras con forjados reticulares," Revista Internacional de Métodos Numéricos para Cálculo y Diseño en Ingeniería, vol. 28, no. 4, pp. 256–267, 2012. DOI: https://doi.org/10.1016/j.rimni.2012.08.003
S. Kim, D. J. Kim, S.-W. Kim, and C. Park, "Tensile behavior characteristics of high-performance slurry-infiltrated fiber-reinforced cementitious composite with respect to fiber volume fraction," Materials, vol. 12, no. 20, 2019, Art. no. 3335. DOI: https://doi.org/10.3390/ma12203335
F. Soltanzadeh, A. E. Behbahani, K. Hosseinmostofi, and C. A. Teixeira, "Assessment of the sustainability of fibre-reinforced concrete by considering both environmental and mechanical properties," Sustainability, vol. 14, no. 10, 2022, Art. no. 6347. DOI: https://doi.org/10.3390/su14106347
C. Ryan, E. Garcia-Taengua, C. Chalioris, and E. Bastidas-Arteaga, "Fibre-reinforced concrete is sustainable and cost-effective for water-retaining structures, " Sustainability, vol. 13, no. 20, 2021, Art. no. 11479. DOI: https://doi.org/10.3390/su132011479
L. Chen et al., "Recent developments on natural fiber concrete: A review of properties, sustainability, applications, barriers, and opportunities," Developments in the Built Environment, vol. 16, 2023, Art. no. 100255. DOI: https://doi.org/10.1016/j.dibe.2023.100255
S. P. Chandar and S. K. S. Kumar, "Mechanical properties of fiber reinforced concrete – natural fibers: A review, " Materials Today: Proceedings, vol. 68, pp. 2066–2071, 2022. DOI: https://doi.org/10.1016/j.matpr.2022.08.362
C. M. Bittner and V. Oettel, "Fiber reinforced concrete with natural plant fibers—Investigations on the application of bamboo fibers in ultra-high performance concrete," Sustainability, vol. 14, no. 19, 2022, Art. no. 12011. DOI: https://doi.org/10.3390/su141912011
A. Rajkohila and S. P. Chandar, "A critical review on the effect of natural fiber in high strength concrete," in AIP Conference Proceedings, vol. 2515, no. 1, 2022. DOI: https://doi.org/10.1063/5.0103022
M. M. Rao, S. K. Patro, and P. K. Acharya, "Utilisation of plastic waste as synthetic fiber and aggregate in concrete – A review," The Open Civil Engineering Journal, vol. 17, 2023, Art. no. e187414952301100. DOI: https://doi.org/10.2174/18741495-v17-e230113-2022-HT31-3975-4
J.-K. Park and M.-O. Kim, "Mechanical properties of cement-based materials with recycled plastic: A review," Sustainability, vol. 12, no. 21, 2020, Art. no. 9060. DOI: https://doi.org/10.3390/su12219060
F. R. B. Martinelli, F. R. C. Ribeiro, M. T. Marvila, S. N. Monteiro, F. da C. G. Filho, and A. R. G. de Azevedo, "A review of the use of coconut fiber in cement composites," Polymers, vol. 15, no. 5, 2023, Art. no. 1309. DOI: https://doi.org/10.3390/polym15051309
L. A. Abdulateef, S. H. Hassan, and A. M. Ahmed, "Exploring the Mechanical Behavior of Concrete enhanced with Fibers derived from recycled Plastic Bottles," Engineering, Technology & Applied Science Research, vol. 14, no. 2, pp. 13481–13486, Apr. 2024. DOI: https://doi.org/10.48084/etasr.6895
A. Geremew, A. Outtier, P. De Winne, T. A. Demissie, and H. De Backer, "An experimental investigation on the effect of incorporating natural fibers on the mechanical and durability properties of concrete by using treated hybrid fiber-reinforced concrete application," Fibers, vol. 13, no. 3, 2025, Art. no. 26. DOI: https://doi.org/10.3390/fib13030026
M. Alanazi et al., "A comprehensive review on sustainable natural fiber in cementitious composites: The date palm fiber case," Sustainability, vol. 14, no. 11, 2022, Art. no. 6691. DOI: https://doi.org/10.3390/su14116691
I. R. Abubakar et al., "Environmental sustainability impacts of solid waste management practices in the global south," International Journal of Environmental Research and Public Health, vol. 19, no. 19, 2022, Art. no. 12717. DOI: https://doi.org/10.3390/ijerph191912717
Z. Zhang et al., "Municipal solid waste management challenges in developing regions: A comprehensive review and future perspectives for Asia and Africa," Science of The Total Environment, vol. 930, June 2024, Art. no. 172794. DOI: https://doi.org/10.1016/j.scitotenv.2024.172794
H. I. Abdel-Shafy and M. S. M. Mansour, "Solid waste issue: Sources, composition, disposal, recycling, and valorization," Egyptian Journal of Petroleum, vol. 27, no. 4, pp. 1275–1290, 2018. DOI: https://doi.org/10.1016/j.ejpe.2018.07.003
Global Plastics Outlook: Policy Scenarios to 2060. Paris, France: OECD Publishing, 2022.
A. Chamas et al., "Degradation rates of plastics in the environment," ACS Sustainable Chemistry & Engineering, vol. 8, no. 9, pp. 3494–3511, 2020. DOI: https://doi.org/10.1021/acssuschemeng.9b06635
[R. Geyer, J. R. Jambeck, and K. L. Law, "Production, use, and fate of all plastics ever made," Science Advances, vol. 3, no. 7, 2017, Art. no. e1700782. DOI: https://doi.org/10.1126/sciadv.1700782
W. Stelte, N. Reddy, S. Barsberg, and A. Sanadi, "Coir from coconut processing waste as a raw material for applications beyond traditional uses," BioResources, vol. 18, no. 1, pp. 2187–2212, 2023. DOI: https://doi.org/10.15376/biores.18.1.Stelte
F. Vieira et al., "Coconut waste: Discovering sustainable approaches to advance a circular economy," Sustainability, vol. 16, no. 7, 2024, Art. no. 3066. DOI: https://doi.org/10.3390/su16073066
C. G. Coviello, A. La Scala, M. F. Sabbà, and L. Carnimeo, "On the cementitious mixtures reinforced with waste polyethylene terephthalate," Materials, vol. 17, no. 21, 2024, Art. no. 5351. DOI: https://doi.org/10.3390/ma17215351
M. K. Askar, Y. S. S. Al-Kamaki, and A. Hassan, "Utilizing polyethylene terephthalate (PET) in concrete: A review," Polymers, vol. 15, no. 15, 2023, Art. no. 3320. DOI: https://doi.org/10.3390/polym15153320
M. V. Barros and R. Salvador, "Strategies for sustainable reuse of green coconut biomass in a Southern Brazilian coastal region: Perspectives from a circular economy," Procedia CIRP, vol. 135, pp. 1058–1063, 2025. DOI: https://doi.org/10.1016/j.procir.2024.12.108
A. Meza, P. Pujadas, L. M. Meza, F. Pardo-Bosch, and R. D. López-Carreño, "Mechanical optimization of concrete with recycled PET fibres based on a statistical-experimental study," Materials, vol. 14, no. 2, 2021, Art. no. 240. DOI: https://doi.org/10.3390/ma14020240
S.-J. Lee, H. Shin, H.-N. Lee, S.-H. Park, H.-M. Kim, and C.-G. Park, "Effect of waste PET fiber on the mechanical properties and chloride ion penetration of emergency repair concrete for road pavement," Materials, vol. 17, no. 21, 2024, Art. no. 5352. DOI: https://doi.org/10.3390/ma17215352
F. Fraternali, V. Ciancia, R. Chechile, G. Rizzano, L. Feo, and L. Incarnato, "Experimental study of the thermo-mechanical properties of recycled PET fiber-reinforced concrete," Composite Structures, vol. 93, no. 9, pp. 2368–2374, 2011. DOI: https://doi.org/10.1016/j.compstruct.2011.03.025
W. Ahmad et al., "Effect of coconut fiber length and content on properties of high strength concrete," Materials, vol. 13, no. 5, 2020, Art. no. 1075. DOI: https://doi.org/10.3390/ma13051075
M. Ali, A. Liu, H. Sou, and N. Chouw, "Mechanical and dynamic properties of coconut fibre reinforced concrete," Construction and Building Materials, vol. 30, pp. 814–825, 2012. DOI: https://doi.org/10.1016/j.conbuildmat.2011.12.068
A. Varghese and S. Unnikrishnan, "Mechanical strength of coconut fiber reinforced concrete," Materials Today: Proceedings, 2023. DOI: https://doi.org/10.1016/j.matpr.2023.05.637
H. Hijriah, N. Z. Muhding, M. F. Wahab, A. Fauzi, R. M. K. Yanti, and R. B. Sukmara, "The effect of adding coconut coir fiber on compressive strength, tensile strength, and concrete flexural strength in eco-friendly tetrapod planning in coastal areas of IKN supporting cities," Journal of Civil Engineering and Vocational Education (CIVED), vol. 11, no. 1, pp. 120–134, 2024. DOI: https://doi.org/10.24036/cived.v11i1.515
A. J. Babafemi, T. Kolawole, and O. B. Olalusi, "Mechanical and durability properties of coir fibre reinforced concrete," Journal of Engineering Science and Technology, vol. 14, no. 3, pp. 1482–1496, 2019.
The 2030 Agenda and the Sustainable Development Goals: An Opportunity for Latin America and the Caribbean. Global Goals, Targets, and Indicators. Vitacura, Santiago de Chile: CEPAL, 2016.
C150/C150M-22 Standard Specification for Portland Cement. West Conshohocken, PA, USA: ASTM International, 2023.
C127-24: Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate. West Conshohocken, PA, USA. ASTM International, 2024.
C136/C136M-19: Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates. West Conshohocken, PA, USA, ASTM International, 2019.
C29/C29M-07 Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate. West Conshohocken, PA, USA: ASTM International, 2010.
C566-19 Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying. West Conshohocken, PA, USA: ASTM International, 2019.
C128-22 Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate. West Conshohocken, PA, USA: ASTM International, 2022.
C1602/C1602M-22 Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete. West Conshohocken, PA, USA: ASTM International, 2022.
C494/C494M-24 Standard Specification for Chemical Admixtures for Concrete. West Conshohocken, PA, USA: ASTM International, 2024.
D. L. Rocha, L. Tambara Júnior, M. Marvila, E. Pereira, D. Souza, and A. de Azevedo, "A review of the use of natural fibers in cement composites: Concepts, applications and Brazilian history," Polymers, vol. 14, no. 10, 2022, Art. no. 2043. DOI: https://doi.org/10.3390/polym14102043
PRC-211.1-91: Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete. Farmington Hills, MI, USA: ACI, 1991.
L. Moreno Alcívar, R. Castro Valle, G. Herrera Franco, M. Muñoz Rosado, and E. Altamirano Espinoza, "Impact of adding PET fibers to concrete," in Proceedings of the 23rd LACCEI International Multi-Conference for Engineering, Education and Technology (LACCEI), 2025. DOI: https://doi.org/10.18687/LACCEI2025.1.1.1885
C39/C39M-21 Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. West Conshohocken, PA, USA: ASTM International, 2023.
1573 - Method for Determining Compressive Strength of Concrete. Quito, Equador: INEN, 2015.
C78/C78M-22 Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading). West Conshohocken, PA, USA: ASTM International, 2023.
2554: Concrete Flexure - Technical Standard. Quito, Equador: INEN, 2011.
D570-22 Standard Test Method for Water Absorption of Plastics. West Conshohocken, PA, USA: ASTM International, 2022.
C192/C192M-25a Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory. West Conshohocken, PA, USA: ASTM International, 2023.
R. D. Tolêdo Filho, K. Scrivener, G. L. England, and K. Ghavami, "Durability of alkali-sensitive sisal and coconut fibres in cement mortar composites," Cement and Concrete Composites, vol. 22, no. 2, pp. 127–143. DOI: https://doi.org/10.1016/S0958-9465(99)00039-6
Downloads
How to Cite
License
Copyright (c) 2026 Genesis Soriano Perez, Lucrecia Moreno Alcivar, Rebeca Castro Valle
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain the copyright and grant the journal the right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) after its publication in ETASR with an acknowledgement of its initial publication in this journal.
